A Non-Roofers Guide to Roofing Terms. The New Hampshire Roofing Glossary:
Before you spend your money. The more you know, the better equipped you will be to make decisions about your roof. Benchmark Home Improvements doesn’t expect you to become roofing experts over night, but with this guide you can have a basic understanding of roofing terms. We do encourage our customers to get to know as much about their New Hampshire roofing systems as possible. Here is our Seacoast, NH and Maine roofing glossary, a list of common roofing terms you might hear during the course of your roofing project.
Coatings. Different coatings are used in metal roofing applications, including
polyvinylidene (PVDF) paint, stone coating (using mineral granules similar to those on
shingles), or polyester resin.
Counter flashing: That portion of the flashing attached to a vertical surface to prevent
water from seeping behind the base flashing.
Cricket: A peaked saddle construction at the back of a chimney to prevent accumulation
of snow and ice and to deflect water around the chimney.
Deck or decking: The surface installed over the supporting framing members of a roof.
Many homes have decking made of plywood.
Drip edge: A non-corrosive, non-staining material used along the eaves and rakes to
allow water runoff to drip clear of underlying construction.
Eaves: The horizontal, lower edge of a sloped roof.
Fascia: Vertical panels capping the perimeter of the gables and eaves of the roof.
Felt: A flexible sheet that is saturated with asphalt and used as an underlayment,
sometimes referred to as tar paper.
Fire Ratings: Fire resistance ratings are established for roofing by ASTM and UL tests.
These indicate the resistance of a roofing system to fires originating from sources
outside the building.
- Class “A”: The highest fire-resistance rating for roofing. Indicates roofing is able
to withstand severe exposure to fire originating from sources outside the
- Class “B”: Fire-resistance rating that indicates roofing materials are able to
withstand moderate exposure to fire originating from sources outside the
- Class “C”: Fire-resistance rating that indicates roofing materials are able to
withstand light exposure to fire originating from sources outside the building.
Flange: Metal collar placed over a vent pipe to seal the roof around the vent pipe
opening. Sometimes called a pipe boot.
Flashing: Pieces of special trim used to prevent seepage of water into a building around
any intersection or projection in a roof such as vent pipes, chimneys, adjoining walls,
dormers and valleys.
Gable: The upper portion of a side wall that forms a triangular point at the ridge of a
Gable roof: A type of roof containing sloping planes of the same pitch on each side of
Galvalume steel: Carbon steel with a protective alloy consisting primarily of aluminum
on both sides of the steel.
Galvanized steel: Carbon steel with a protective alloy consisting primarily of zinc on
both sides of the steel.
Gambrel roof: A type of roof containing two sloping planes of different pitch on each
side of the ridge. The lower plane has a steeper slope than the upper.
Gauge is the term used to indicate the standard thickness of sheet metal, such as that
used on a roof.
Hip roof: A type of roof containing sloping planes of the same pitch on each of four
sides. This type of roof does not have gables at the ends.
Ice dam: Ice dams can form when the surface of a roof heats up, usually from heat
generated in the attic below the roof deck, melting accumulated snow or ice. The
melted snow trickles down to the roof’s edge where it is again exposed to frigid air and
refreezes, forming a “dam” of ice that can block additional water from reaching the
gutters. This water can then be forced under the roof deck and into the home, causing structural damage.
The best prevention to ice dams is a well-ventilated roof, combined with adequate attic
insulation to keep the roof deck temperature in balance with the external temperature.
Additional protection for your roof can come in the form of an impermeable ice
and water membrane.
Low slope roof: A roof that slopes between one and two inches per foot.
Mansard roof: A type of roof containing two sloping planes of different pitch on each of
four sides. The lower plane has a much steeper pitch than the upper, often approaching
vertical. This type of roof contains no gables.
Metal drip edge: This refers to trim, usually gable and eave trim, that has a slight bend
at the edge that facilitates water runoff, away from the building.
Overhang: That portion of the roof structure that extends beyond the exterior walls of a
Rafter: The supporting framing member immediately beneath the deck, sloping from
the ridge to the eave.
Rake: The inclined edge of a sloped roof over a wall from the eave to the ridge.
Re-cover: The installation of a new roof system over an existing system without
removing an existing system. Also called “overlay.”
Re-roofing: Installing a new roof system on a building that is not new.
Ridge: The top section of the roof running the length of the roof, where the two roof
Ridge vent: A vent for air built into the ridge flashing. For proper performance a ridge
vent must be coupled with adequate intake vents in the eave soffits of the home.
Rise: The vertical distance from the eaves line to the ridge.
Run: The horizontal distance from the eaves to a point directly under the ridge.
Slope: Also known as pitch. Slope is the measure of how steep a roof is. The slope of the
roof is a factor in determining the kinds of materials that can be used and the longevity o
f the roof. Usually, a steeper roof (higher pitch) will last longer due to its better
drainage. Most metal roofs can be installed on roof pitches of 4:12 or greater though
many systems can be installed on shallower roofs.
- Steep slope: Roof slopes greater than 21 inches per foot.
- Normal slope: Roof slopes between 4 inches and 21 inches per foot.
- Low slope: Roof slopes between two and four inches per foot.
Soffit: The finished underside of the eaves.
Span: The horizontal distance from eaves to eaves.
Square: A unit of roof measure covering 100 square feet.
Tear off: Removing an existing roof system.
Telegraphing: A distortion that may arise when a new roof is applied over an uneven surface.
Underlayment: Material laid down over roof decking to serve as a barrier layer under
the outside roofing material (metal, shingles, tiles, etc.). Serves to prevent water
seepage. Specialized underlayment can also help prevent the formation of ice dams
along the roof’s edge. Underlayment is required by code beneath all metal roofs, even if
the old shingles are left in place.
Valley: The internal angle formed by the intersection of two sloping roof planes to
provide water runoff.
Vent: Any outlet for air that protrudes through the roof deck such as a pipe or furnace
chimney. Also, any device installed on the roof, gable or soffit for the purpose of
ventilating the underside of the roof deck.
Don’t You Want a Contractor You Can Trust For Quality Workmanship?
Call Today (603) 272-1147